CCNA Discovery 2 - Cisco Discovery - DsmbISP Module 6 - V.4 .

Q.1 Which command is used to view the RIP routing protocol settings and configuration?

show version
show ip route
show interface
show ip protocols


Q.2 Refer to the exhibit. What is the maximum number of RIP routers that could separate HostA and HostB and still leave the hosts with connectivity to each other?

14
15
16
17


Q.3 In which situation would a company register for its own autonomous system number (ASN)?

when the company's ISP adds connection points to the Internet
when additional routers are added to the corporate internetwork
when more than one interior routing protocol is used
when the company uses two or more ISPs


Q.4 Consider this routing table entry

R 172.16.1.0/24 [120/1] via 200.1.1.1 00:00:27 Serial0/1

What type of route is this?
a static route
a default route
a RIP route
an OSPF route
an EIGRP route
a directly-connected route


Q.5 What is the difference between interior and exterior routing protocols?

Exterior routing protocols are only used by large ISPs. Interior routing protocols are used by small ISPs.
Interior routing protocols are used to route on the Internet. Exterior routing protocols are used inside organizations.
Exterior routing protocols are used to administer a single autonomous system. Interior routing protocols are used to administer several domains.
Interior routing protocols are used to communicate within a single autonomous system. Exterior routing protocols are used to communicate between multiple autonomous systems.


Q.6 What information is included in RIPv2 routing updates that is not included in RIPv1 updates?

metric
subnet mask
area identification
hop count
autonomous system number


Q.7 Which routing protocol is used to exchange data between two different ISPs?

BGP
EIGRP
OSPF
RIP v2



Q.8 Refer to the exhibit. Which configuration command or commands contributed to the output that is shown?

routerA(config-router)# no version 2
routerA(config)# interface fa0/0
     routerA(config-if)# ip address 172.19.0.0 255.255.0.0
routerA(config-router)# network 192.168.3.0
routerA(config)# no ip default-gateway



Q.9 Refer to the exhibit. If all routers are running RIP and network 10.0.0.0 goes down, when will R3 learn that the network is no longer available?

in 30 seconds
in 60 seconds
in 90 seconds
Immediately


Q.10 What statement is true regarding an AS number?

AS numbers are controlled and registered for Internet use.
Interior routing protocols require registered AS numbers.
ISPs require all customers to have registered AS numbers.
All routers at an ISP must be assigned the same AS number.


Q.11 What is the purpose of the network command used when configuring RIP?

to specify whether RIPv1 or RIPv2 will be used as the routing protocol
to allow the router to monitor RIP updates that occur on other routers
to identify which networks on the router will send and receive RIP updates
to configure the IP address on an interface that will use RIP
to identify all of the remote networks that should be reachable from the router


Q.12 Which command would a network administrator use to determine if the routers in an enterprise have learned about a newly added network?

router# show ip address
router# show ip route
router# show ip networks
router# show ip interface brief
router# debug ip protocol
router# debug rip update


Q.13 What is the purpose of a routing protocol?

It is used to build and maintain ARP tables.
It provides a method for segmenting and reassembling data packets.
It allows an administrator to devise an addressing scheme for the network.
It allows a router to share information about known networks with other routers.
It provides a procedure for encoding and decoding data into bits for packet forwarding.


Q.14 What device enables an ISP to connect with other ISPs to transfer data?

border gateway router
DSLAM
web server
interior router


Q.15 Which command will display RIP routing updates as they are sent and received?

show ip route
show ip rip
debug ip rip
show ip protocols
show ip rip database


Q.16 Which part of an IP packet does the router use to make routing decisions?

source IP address
source MAC address
destination IP address
destination MAC address


Q.17 What two types of businesses would benefit from registering as their own autonomous systems? (Choose two.)

a home business with one ISP connection
a global business with connections to multiple local ISPs
a medium-sized nationwide business with Internet connectivity through different ISPs
a large enterprise with two connections to the same ISP
a small ISP with a single Internet connection through a larger ISP


Q.18 Which command will display RIP activity as it occurs on a router?


show ip route
show ip interface
show ip protocols
debug ip rip config
show ip rip database


Q.19 Why is fast convergence desirable in networks that use dynamic routing protocols?

Routers will not allow packets to be forwarded until the network has converged.
Hosts are unable to access their gateway until the network has converged.
Routers may make incorrect forwarding decisions until the network has converged.
Routers will not allow configuration changes to be made until the network has converged.


Q.20 Which two statements describe static routes? (Choose two.)

They are created in interface configuration mode.
They require manual reconfiguration to accommodate network changes.
They automatically become the default gateway of the router.
They are identified in the routing table with the prefix S
They are automatically updated whenever an interface is reconfigured or shutdown.


Q.21 Which two statements or sets of statements describe differences between link-state and distance vector routing protocols? (Choose two.)

Link-state routing protocols routinely use more bandwidth for updates than do distance vector routing protocols.
Distance vector routing protocols update all routers at one time. Link-state routing protocols update one router at a time.
Link-state routers only know about directly connected routers. Distance vector routers know about every router in the network.
Link-state routing protocols update when a change is made. A network using distance vector routing protocols only updates at a specific interval.
Distance vector routing protocols have limited information about the entire network. Link state routing protocols know about all routers in the network.
In case of similar topologies, networks using link-state routing protocols typically converge more rapidly than do networks using distance vector routing protocols.


Q.22 Which protocol is an exterior routing protocol?

BGP
EIGRP
OSPF
RIP


Q.23 Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)

Ping
show arp
Traceroute
show ip route
show interface
show cdp neighbor detail


Q.24 What term refers to a group of networks that uses the same internal routing policies and is controlled by a single administrative authority?

Internet
intranet
virtual private network
autonomous system